Оглавление
A transformer bushing is simultaneously an insulation system, a current-carrying connection, a mechanical cantilever, and a sealed interface through the transformer tank or cover. Transformer bushing selection therefore cannot be completed by matching nominal voltage and amperes. The surrounding network, terminal arrangement, pollution, altitude, forces, internal lead, CTs, and replacement strategy all matter.
This guide helps transformer buyers, system engineers, EPC teams, and maintenance planners turn transformer bushing selection into a controlled interface review. It covers dielectric duty, thermal loading, external insulation, mechanical loads, dimensions, monitoring, and test evidence.
Start with insulation coordination, not nominal voltage
Use highest system voltage and the project’s insulation-coordination study. Specify power-frequency and impulse withstand requirements, system grounding, temporary overvoltage, switching duty, lightning exposure, and surge-arrester protection. Transformer bushing selection should coordinate with the transformer winding, terminal enclosure, cable, bus duct, and adjacent equipment.
Arrester lead length and grounding can affect the stress that reaches the bushing. A suitable arrester rating on a distant bus may not provide the same protection as a correctly located device. Review the transformer bushing selection protective margin and physical layout together.
Distinguish indoor air-to-air, oil-to-air, oil-to-cable-box, plug-in, and other interfaces. The external and internal insulation media define different creepage, clearance, sealing, and test requirements. Record both sides of transformer bushing selection on one drawing.
- Highest system voltage and insulation test levels
- Winding connection and system grounding
- Surge-arrester location and protective level
- Indoor, outdoor, cable-box, or bus-duct interface
- Altitude, pollution, humidity, and condensation
- Phase spacing and grounded clearances

Rate current for loading and terminal heating
Continuous current should cover normal loading, approved overload, harmonic duty, ambient temperature, terminal heating, and cooling conditions. Transformer bushing selection needs a temperature-rise check at the central conductor, contacts, terminals, and surrounding oil or air.
Transformer bushing selection must address connection resistance because a poorly prepared palm can create a hot spot even when the bushing nameplate current is adequate. Specify terminal material, plating, hole pattern, bolt arrangement, surface preparation, washers, and tightening method. Coordinate copper-to-aluminium transitions.
For parallel cables or bus duct, calculate current sharing and proximity effects. Do not assume equal current through several connections. The transformer bushing selection rating must remain adequate for credible imbalance and contingency loading.
Match creepage and materials to the environment
External insulation must suit pollution severity, rain, fog, salt, industrial deposits, altitude, ultraviolet exposure, and cleaning practice. Transformer bushing selection should state required creepage, shed profile, housing material, and any altitude correction rather than using “outdoor” as the full requirement.
Porcelain and composite housings have different handling, weight, impact, hydrophobicity, aging, and inspection characteristics. Neither is universally superior. Transformer bushing selection should evaluate manufacturer evidence, service environment, seismic requirement, transport, and maintenance capability.
In a cable box, condensation and restricted clearance may govern. Heaters, drains, seals, ventilation, and cable-entry protection must work with the bushing. A long creepage path does not solve water dripping onto the terminal.

Control cable, bus, and overhead connection forces
Obtain allowable cantilever, tensile, torsional, and terminal loads. Then calculate forces from conductor weight, wind, ice, short-circuit current, seismic motion, cable stiffness, bus expansion, and installation tolerances. Transformer bushing selection should not make the bushing support an unrestrained cable or misaligned bus duct.
Provide independent cable cleats, flexible links, bus supports, and expansion joints where required. Transformer bushing selection must coordinate the neutral bushing as carefully as phase bushings because a large neutral conductor or grounding resistor connection can impose significant force.
Show the load direction and application point on the interface drawing. A force within one-axis limit may exceed a combined-load envelope. Verify transport braces and remove them through a controlled commissioning step.
| Bushing choice | Useful characteristic | Review point |
|---|---|---|
| Porcelain housing | Established external insulation system | Mass, brittleness, seismic and handling risk |
| Composite housing | Lower mass and hydrophobic surface options | Material aging, pollution, sealing, manufacturer evidence |
| Draw-lead connection | Lead is pulled through the central conductor | Current limit, installation procedure, lead dimensions |
| Bottom-connected design | Rigid internal connection at the lower terminal | Exact geometry, access, torque, and assembly sequence |
| Condenser-graded bushing | Controls electric field through the insulation body | Test tap, capacitance, power factor, oil or resin system |
Freeze the transformer-side dimensional interface
Freeze flange size, bolt circle, oil-side length, draw-lead or bottom connection, conductor diameter, terminal height, phase spacing, cover slope, oil level, shield arrangement, and required assembly access. Transformer bushing selection changes can affect winding leads and tank electric fields.
Check the internal lead for current, flexibility, insulation, bending radius, and installation sequence. A draw lead must pass through the central conductor without damage and terminate according to the bushing procedure. A bottom connection needs controlled access and torque.
Replacement interchangeability should be proven through a dimensional comparison, not a shared catalog description. Keep a controlled bushing drawing and identify acceptable alternatives only after transformer bushing selection review.
Coordinate bushing CTs and monitoring features
Bushings may incorporate current transformers for protection and metering. Specify CT ratio, class, cores, burden, polarity, knee-point or transient performance as required, secondary terminals, and physical order. Transformer bushing selection must reserve adequate space and coordinate CT orientation with protection zones.
Condenser bushings may provide test taps for capacitance and dielectric-loss measurements. Define tap rating, grounding cap, accessibility, and monitoring connection. An ungrounded or incorrectly connected tap can damage the bushing.
Online monitoring can trend capacitance, power factor, leakage current, or temperature, but alarms need baseline values, compensation, and a response plan. Monitoring supplements inspection and testing; it does not make transformer bushing selection errors acceptable.

Plan handling, replacement, and field testing
Plan lifting points, storage orientation, protective packaging, cleanliness, drying or oil handling, installation tools, and weather limits. Transformer bushing selection should consider whether the site can safely replace the component without removing unrelated equipment.
Define field inspection and electrical tests appropriate to bushing type. Visual inspection, insulation resistance, capacitance, dielectric loss, oil checks, leakage, thermography, and partial-discharge methods answer different questions. Follow manufacturer limits and establish an as-left baseline.
Store transformer bushing selection test results with temperature, test voltage, instrument, tap connections, and bushing identity. Trend comparable readings. A single value without method and history provides weak maintenance evidence.
Approve evidence for the exact offered bushing
Require drawings, data sheets, material descriptions, type-test evidence, routine-test reports, nameplate details, installation instructions, and deviation statements. Transformer bushing selection approval should reference the exact model and manufacturing configuration.
At factory inspection, verify ratings, dimensions, terminals, CT data, test tap, oil level or filling condition, seals, packing, and routine reports. Confirm that transformer assembly tests use the offered bushings or a reviewed equivalent.
Relevant product information includes the oil-immersed transformer, dry-type transformer, the complete product range, and the technical contact page. Send cable or bus interface drawings for transformer bushing selection support.
Authoritative references include the International Electrotechnical Commission, IEEE Standards Association, CIGRE, and the NFPA codes and standards program. Use the project’s adopted editions and local requirements.
Часто задаваемые вопросы
Can bushings with the same voltage and current be interchanged?
Not automatically. Dimensions, insulation, terminals, CTs, internal lead, test taps, forces, and transformer electric fields must also match.
Is composite insulation always better than porcelain?
No. Weight and surface behavior may help, while material aging and service evidence need review. Select for the actual environment and mechanical duty.
Why are cable supports part of bushing selection?
Unsupported cables can apply weight, thermal movement, and short-circuit force beyond the bushing’s terminal limits.
What does a bushing test tap do?
It provides access to the capacitive grading system for approved measurements or monitoring and must be correctly grounded when not in use.
What information should be provided to the manufacturer?
Provide system voltage and insulation levels, current duty, environment, altitude, terminal arrangement, forces, dimensions, CTs, monitoring, and replacement requirements.
For a project-specific transformer bushing selection review, provide the transformer outline and cover drawing, internal lead data, cable or bus arrangement, insulation-coordination study, loading profile, environmental conditions, mechanical calculations, and required tests.


